Sean Reyes | Page 6 | MotorSafety.org

sreyes

BMW Recalls Two M340i Vehicles Due to Rear Center Headrest Defect

September 27, 2019 Sean Reyes BMW Recalls

Laguna Hills, CA – September 26, 2019 – BMW has announced the recall of two vehicles, one 2020 M340i and one M340i xDrive, due to a rear center headrest that may fold improperly in the event of a rear-impact crash.

If the headrest were to fold down in such a setting, the risk of injury to the occupant would dramatically increase.

The defect

During production of both vehicles listed for the recall, the head restraint interlock was not welded sufficiently to the head restraint support rod bracket, according to paperwork filed by BMW with the National Highway Traffic Safety Administration.

As of September 26, manufacturer has not received any reports, nor is it otherwise aware, of any accidents or injuries caused by the defect.

However, the improper production could lead to a break of the weld in the event of a collision, which in turn increases the risk of injury for the occupant in the rear center seat.

Timeline of events

On July 29, BMW first became aware of an instance where a foldable rear center head restraint did not function as intended via an internal rear crash validation test. Further analysis ascribed the defect in that case to a broken weld of the interlock on the head restraint frame.

“A check of other parts was initiated,” according to the chronology that BMW filed with the NHTSA, “and two additional suspect head restraints were found.”

The vehicles included in the recall were produced between July 4 and July 31. BMW reviewed vehicle assembly information and supplier production records in order to determine the specific vehicles that carry the defect.

Their investigation resulted in the identification of two specific vehicles in which the head restraint interlock was not properly welded.

On August 7, BMW decided to conduct a voluntary recall on the two vehicles suspected to carry the defect. The manufacturer’s paperwork notes that dealers were notified August 14, and that notification to owners “is expected to begin and end on October 7, 2019.”

The solution

BMW plans to notify the owners or dealers currently in possession of the two automobiles, at which point local dealers will replace the rear center headrests of the vehicles on the manufacturer’s behalf.

For more information on other BMW recalls, be sure to visit MotorSafety.org.

Some 2020 Jeep Gladiator Trucks Recalled For Rear Driveshafts

September 27, 2019 Sean Reyes Jeep Recalls

Laguna Hills, CA – Sept. 26, 2019 – Fiat Chrysler Automobiles has announced the recall of certain 2020 Jeep Gladiator vehicles that were outfitted with rear driveshafts that may have been incorrectly assembled. The manufacturer estimates that 3,427 vehicles will be affected by the recall, and that roughly 5 percent among that number contain the defect.

The Defect

The defect relates to the monoblock joint, which is a constant velocity joint within the center of the driveshaft.

Chrysler’s depiction of the defect, which they included with paperwork filed to the National Highway Traffic Safety Administration, stated: “Certain 2020 MY Jeep Gladiator vehicles built from December 15, 2018 through June 25, 2019 may have a rear driveshaft that was assembled without grease in the monoblock joint portion of the driveshaft.”

Due to the lack of grease, the driveshaft may fracture, which could cause a sudden loss of driving power if the vehicle is in rear-wheel drive mode. Additionally, the driveshaft itself could separate completely from the vehicle and then become a road hazard. To rectify both safety risks, as well as others that may come as a result of the faulty driveshaft, Chrysler has enacted a recall on vehicles that may contain the defect.

Chrysler notes that in vehicles which contain the defect, if the part were to fail as a result, occupants may experience a noise or vibration prior to the driveshaft fracturing.

Timeline of Events

According to the paperwork filed with the NHTSA, Chrysler first became aware of the potential for the defect in June 2019, when it received four rear driveshafts from warranty repairs that had initially been assembled without grease in the monoblock joint. It was determined that the cause of the defect was that the grease bypass button had been activated at the assembly line station while the given parts were being manufactured.

Based on those cases, Chrysler opened an investigation into the matter, and eventually identified additional examples of the defect, including four additional warranty claims (although the company found no field reports, accidents, or injuries relating to the defect). On Aug. 22, 2019, Chrysler determined, in collaboration with the Vehicle Regulations Committee, to conduct a recall of the Jeep Gladiator vehicles that may potentially lack grease in the monoblock joint portion of the rear driveshaft.

“The suspect population was determined by reviewing the supplier’s driveshaft production records from the beginning of production of this driveshaft to identify which driveshafts may have been assembled without grease,” according to Chrysler’s records. “Driveshaft traceability records were then linked to vehicle production records to determine the suspect vehicle population.”

The Solution

Chrysler will begin notifying both dealers and owners of vehicles which may contain the defect on Oct. 18. Dealers will inspect the vehicles, and verify that the driveshaft contains grease in the monoblock joint. If not, the driveshaft will be replaced free of charge. Sales of vehicles which may contain the defect have been stopped until this repair has been made.

For more information on Chrysler recalls, and other news involving major automobile manufacturers, visit MotorSafety.org.

Chrysler Recalls Ram Trucks with Faulty Tailgate Locks

September 27, 2019 Sean Reyes RAM Recalls

Laguna Hills, CA – Sept. 25, 2019 – Fiat Chrysler Automobiles has announced the recall of a wide range of Ram trucks equipped with an 8-foot bed and a power-locking tailgate, due to the possibility that the tailgate actuator limiter tab may fracture and cause the tailgate to unlock and open while the vehicle is in motion.

While the defect is contained in certain Ram trucks made across roughly five years, not all vehicles manufactured during that period of time have been included in the recall, so vehicle owners should be sure to check whether or not their truck requires the remedy.

The Defect

Chrysler’s description of the defect explains that the tailgate actuator limiter tab located within the power-lock actuator control assembly “may fracture, allowing the lock rod control bracket to over-travel which may pull the lock rods and release the latches, potentially resulting in the tailgate inadvertently falling open at any time.”

The list of vehicles that may contain the defect has been expanded multiple times since the recall was first announced. As of Sept. 25, the makes and models of vehicles that could be affected are as follows:

2013-2018 Ram 1500
2013-2018 Ram 2500
2013-2018 Ram 3500

“An unintended opening of the tailgate while driving may result in a loss of unrestrained cargo from the truck bed while driving,” stated Chrysler’s safety recall report, which describes the safety risk caused by the defect. “Lost cargo may create a road hazard to operators and occupants of other vehicles, and can cause such vehicles to crash without prior warning.”

Timeline of Events

On July 19, 2018, the manufacturer first announced that it would conduct a voluntary safety recall on Ram pickup trucks. At that point ,the recall applied to “certain 2015-2017 MY Ram pickup trucks equipped with a power-locking tailgate, excluding vehicles with an 8-foot truck bed.” On May 2, 2019, the recall was expanded to include 2015-2017 Ram trucks with an 8 foot truck bed, as well as 2018 Ram trucks equipped with a power locking tailgate that were built prior to April 1 of that year.

In August 2019, Chrysler identified 54 warranty claims and repair orders that were potentially related to the defect despite having been generated in relation to vehicles not included in the ongoing recall. Following that discovery, on August 22, Chrysler expanded the recall to include the full list of vehicles seen above.

The Solution

Owners of vehicles listed in the initial recall should have already been notified of the defect by Chrysler earlier this year. However, that was before the range of the recall had been expanded. Owners of Ram vehicles that are now being recalled under the expanded action, as well as dealers, will be notified sometime around Oct. 18, 2019. Those with further questions, or who are looking to find out whether or not their Ram vehicle has been included in the recall, may contact the manufacturer’s customer service line at 800-853-1403.

Once truck owners have been notified that their vehicle has been included in the recall, they are instructed to bring their vehicle to a dealer, who will limit the locking actuator travel. The manufacturer is covering all costs incurred by the repair.

For more information on Chrysler recalls and other news from the automotive industry, visit MotorSafety.org.

Improper Programming on Rear Camera Necessitates Large Nissan Recall

September 25, 2019 Sean Reyes Infiniti Recalls, Nissan Recalls

Laguna Hills, CA – Sep. 25, 2019 – Improper programming that potentially affects the back-up camera display included with various 2018-2019 Nissan vehicles has caused the manufacturer to announce a recall applying to more than 1,200,000 automobiles.

On the vehicles being recalled, adjustments made by the driver to the rear camera display settings will be retained at the start of the next backing event—meaning the image seen on the vehicle’s display while backing up will not necessarily represent the default camera perspective. This is not compliant with current federal regulations, necessitating the Nissan recall.

The Defect

The cause for this recall is perhaps better described as a matter of “non-compliance” than as a defect. According to Federal Motor Vehicle Safety Standard No. 111, the rear visibility system of vehicles manufactured on or after May 1, 2018 must return to a default image at the beginning of each backing event, regardless of whatever modifications were selected during prior trips. If the camera is not in the default position at the beginning of each new backing event, then the possibility of collision or accident increases.

On a large number of 2018-2019 Nissan vehicles, the rear camera image does not return to the default position at the start of each backing event, but instead retains any modifications previously selected by the driver. This vehicles are not in compliance with the FMVSS standard, and as a result have to be recalled. The full list of automobiles that are subject to the recall are as follows:

2018-2019 Infiniti Q50
2018-2019 Infiniti Q60
2018-2019 Infiniti Q70
2018-2019 Infiniti QX30
2018-2019 Infiniti QX50
2018-2019 Infiniti QX60
2018-2019 Infiniti QX80
2018-2019 Nissan Altima
2018-2019 Nissan Armada
2018-2019 Nissan Frontier
2018-2019 Nissan GT-R
2018-2019 Nissan Kicks
2018-2019 Nissan LEAF
2018-2019 Nissan Maxima
2018-2019 Nissan Murano
2018-2019 Nissan NV
2018-2019 Nissan NV200
2018-2019 Nissan Pathfinder
2018-2019 Nissan Rogue
2018-2019 Nissan Rogue Sport
2018-2019 Nissan Sentra
2018-2019 Nissan Taxi
2018-2019 Nissan Titan
2018-2019 Nissan Titan Diesel
2018-2019 Nissan Versa Note
2018-2019 Nissan Versa Sedan

Documents filed to the National Highway Traffic Safety Administration by Nissan explain: “The original adjustment settings that were applied to the rear visibility system and are subject to the non-compliance are not used on any other Nissan or Infiniti vehicles [other than those listed above] … Therefore, no other Nissan or Infiniti vehicles are affected by this condition.”

Timeline of Events

Nissan transmitted a non-compliance information report describing the error on September 12, 2019. They estimate that the mistake applies to a total of 1.23 million model year 2018-2019 Nissan and Infiniti vehicles in total, and that all of those vehicles without exception “contain the noncompliance.”

On September 20, 2019, Nissan submitted a safety recall report pertaining to the issue, and clarified the schedule by which vehicle owners will be notified of the defect: Depending on the make and model of their vehicles, customers will be notified either on the week of October 21 or the week of November 4. All Vehicle Identification Numbers on the affected automobiles will be active at the time of the phased dealer notification, according to Nissan, which is scheduled to begin on October 7 and to conclude either on or before November 11.

Solution

Owners of the vehicles containing the noncompliance will be notified sometime in the range of the dates listed above. At that point, they may bring their vehicle to a local dealer, who will reprogram the rear visibility system software at no cost.

The reprogramming will bring the vehicle into compliance by limiting the adjustments that can be made to the camera display to an extent that ensures the view always remains within the range dictated dictated by FMVSS No. 111.

For more information on recalls announced by Nissan or other major automobile manufacturers, continue visiting MotorSafety.org.

GM Expands Prior Recall on Chevrolet Trax Vehicles

September 23, 2019 Sean Reyes Chevrolet Recalls

Laguna Hills, CA – September 23, 2019 – In April of this year, General Motors announced a recall on certain 2017 – 2019 Chevrolet Trax vehicles, due to the possibility that a joint in one or both of the front lower-control arms had been welded in an improper position.

GM recently decided to expand the scope of that recall, as a result of further investigations, so that it now applies to include other Chevrolet Trax vehicles that were built in the period between July 1, 2015 and June 30, 2017.

At the request of the National Highway Traffic Safety Administration, GM is handling the recall as a new field action. However, in practical terms, it counts as a “population extension”— the defect remains the same as the one listed in the prior recall, with no significant differences.

The defect

The defect is now known to exist in certain 2015 – 2018 model year Chevrolet Trax vehicles. GM estimates that 93,639 such vehicles have the potential to contain the defect, and that roughly 50 percent among that number do indeed contain it.

“In some of these vehicles, a joint in one or both front lower-control arms may have been improperly welded,” state details in documents filed by GM with the NHTSA.

“Over time and in rare cases, an improperly welded joint can fatigue and break, causing the lower-control arm to partially separate from the vehicle”.

If the lower-control arm does separate from the vehicle, then the front wheel attached to the arm will toe outward, adversely affecting steering and increasing the possibility of a crash.

According to the GM documents, the defect was caused because “the component surfacer that is welded to the bushing housing did not conform to applicable design specifications, and as a consequence, was not properly welded to the bushing housing.”

The manufacturer is not yet aware of any vehicle crashes that are attributable to the defect, but notes that if the lower-control arm were to partially separate, the driver may hear a loud noise, and feel the tire begin to rub against the wheel well.

Timeline of events

The initial recall, which applied to certain 2017 – 2019 model year Chevrolet Trax vehicles, was announced in April 2019. At the time of that recall, GM was not aware of any claims relating to the defect in question within vehicles built prior to July 2017.

However, in September 2019, GM’s Safety and Field Action Decision Authority reviewed an analysis of field claims generated following the April recall, which found instances of the defect (some confirmed and some unconfirmed) in vehicles built as early as July 2015.

Based on that data, the decision was made to create a new recall that applies to a larger range of Chevrolet Trax vehicles.

The solution

The repair for the defect is currently available, and will be done at no cost to the customer. Customers who own a vehicle potentially containing the defect will be notified by mail by GM. Dealers will inspect the left and right front lower-control arms, and, if necessary, replace them free of charge.

GM notes that they corrected the potential for the defect by implementing new actions at their supplier in April 2019, such as amending the specifications for the welding, and introducing standardized inspections before and after the weld operation.

To find out if your vehicle is part of this recall, MotorSafety.org’s free look-up tool.

Possibility of Fuel Leak Causes Volkswagen to Recall Six 2019 Atlas Vehicles

September 20, 2019 Sean Reyes Volkswagen Recalls

Laguna Hills, CA – Sep. 20, 2019 – Volkswagen has announced that there may have been a defect in the construction of the fuel tank on five or six 2019 Atlas vehicles, leading to a small but extremely consequential vehicle recall. On these particular automobiles, it’s possible that the suction jet in the fuel tank may have been welded in an incorrect position, which could potentially allow fuel to leak from the tank.

On a vehicle containing the defect, this is likely to cause momentum to stall as a result of uneven fuel distribution, which creates the possibility for collision. However, there are of course even more dangerous risks that come along with the defect, including the possibility of an ignition source reaching the leaked fuel and causing a fire.

The Defect

According to paperwork filed with the National Highway Traffic Safety Administration by Volkswagen, fuel tanks manufactured for the Atlas during a limited time frame may have been incorrectly welded, causing the suction jet bracket to border against the fuel tank internal wall. This error was caused during initial production of the part by the supplier, YAPP, due to “Incorrectly performed maintenance [of] the supplier’s tooling,” and was rectified shortly thereafter.

As a result of this defect, the suction jet in the fuel tank may not be located where it should be, which has the potential to cause a fuel tank leak. This significantly increases the possibility of the vehicle being involved in a crash or catching fire. Drivers of the 2019 Atlas vehicle will want to keep watch for the odor of fuel, and the sight of fuel puddles underneath the automobile.

Timeline of Events

The supplier first noted the potential for the defect in late July 2019, according to the report filed by Volkswagen. Following an investigation to determine how many fuel tanks were affected, every tank that potentially contained the defect was quarantined by both YAPP and Volkswagen. Using video of the production of the tanks, YAPP and Volkswagen are able to pinpoint exactly which objects were affected, at which point the manufacturer was able to issue a stop order for shipment and sales of all Atlas vehicles that might contain the defect.

However on July 31, Volkswagen was able to determine that five Atlas vehicles which potentially contain the defect had been sent to dealers, although at that point all five remained unsold. Following further video review on August 1, YAPP determines that at least one of the five vehicles contains the defect, with the others potentially containing it as well. At that point, Volkswagen’s Product Safety Committee was presented with the topic, and determined that a recall was necessary.

The Solution

Volkswagen plans to notify both dealers and owners of the affected Atlas vehicles of the recall either on or before Oct. 11, 2019. At that point, the fuel tank on the affected vehicles will be replaced by the manufacturer at no cost to owners. Additionally, measures have been taken by YAPP to ensure that any fuel tanks with improper welding will not make it past the factory.

For more information on automobile recalls, whether large or small in number, be sure to continue visiting MotorSafety.org.

Issues with Engine Control Modules Leads GM to Announce Malibu Recall

September 19, 2019 Sean Reyes Chevrolet Recalls

Warren, MI – September 21, 2022 – General Motors (NYSE:GM) has remedied issues with 152,605 2018 Chevrolet Malibu vehicles that were dealing with fuel injectors issues caused by problems on the 1.5L turbo engines. Additionally, 1,019 of these GM vehicles have been categorized as unreachable, and 34 have been removed from the recall. One group of these 2018 Chevrolet Malibu was remedied in 2019, four groups in 2020, and another group was remedied in 2021 due to these issues where the ECM may disable the fuel injectors.

Warren, MI – September 19, 2019 – Complications with 1.5L turbo engines have caused the fuel injectors on some 2018 Chevrolet Malibu vehicles to become disabled, leading the car manufacturer to announce a recall for that particular make and model.

Because of the issues, the car engine may be prevented from starting, or drivers could experience stalls, therefore increasing the possibility of collision.

Unfortunately, the updated software designed to fix the defect has not yet been completed—but once it is available, dealers will reprogram the engine control module (ECM) on affected vehicles to prevent the error from occurring.

The defect

According to documents filed by General Motors, the defect applying to the 1.5L turbo engines could potentially affect more than 175,000 vehicles, with the manufacturer estimating that roughly 1 percent of those automobiles contain the defect.

“Under certain conditions, an error in the vehicles’ ECM software can cause data used by the ECM to become corrupted,” stated the description of the defect in GM’s safety recall paperwork, “When this occurs, the ECM may send a signal disabling the engine’s fuel injectors.

If the fuel injectors are disabled, the engine may not start and, in rare cases, the engine may stall after it is started.” This means the vehicle may stall at speed, which would significantly increase the possibility of collision.

However, other makes and models of the Malibu should not contain the defect, as they run off different ECM software.

Finally, to aid drivers in taking necessary precautions, GM has advised that vehicles with this defect may see their check-engine light illuminate if the error arises.

Timeline of events

GM informed the National Highway Traffic Safety Administration of the vehicle recall in a letter dated September 10, 2019.

According to that letter and other documents regarding the defect, GM first became aware of the error in May 2019, when it came to the company’s attention as a result of higher-than-usual warranty rates for ECM replacements in 2018 Malibu vehicles.

The warranty claims illustrated to GM the risks associated with the defect —that engines may fail to start in the first place, or, more dangerously, may stall while the vehicle is moving at speed.

In collaboration with the supplier of the ECMs, Continental Automotive Systems, the manufacturer discovered notable differences between the software used in 2018 and 2019 models of the vehicle, and soon afterwards discovered a defect in the 2018 software which has the potential to disable the engine’s fuel injectors.

The solution

The software update that corrects the ECM issue will be done by dealers at no charge to owners of the automobile. However, that software update is not yet complete, meaning the recall notices will have to wait until the fix is completely prepared.

The bulletin will only be posted once the software update has been completed, at which point drivers who own the vehicle will be able to bring it to their local dealership for the aforementioned fix.

Also, vehicle owners directly affected by the recall will be notified by mail. Dealers themselves were notified of the problem in early September, and more information is sure to follow in the coming weeks and months.

To find out if your vehicle is part of this recall, use MotorSafety.org’s free look-up tool.

General Motors Recalls Various Vehicles Due to Vacuum Pump

September 17, 2019 Sean Reyes Cadillac Recalls, Chevrolet Recalls, GMC Recalls

December 2, 2021 Update – GM has remedied 2,588,566 vehicles with the issue of vacuum pump issues in the 2018 GMC Yukon among others. GM has deemed 21,474 vehicles including the 2018 Chevrolet Silverado unreachable with an additional 207 vehicles being removed from the vacuum pump recall.

Laguna Hills, CA – September 17, 2019 – The possibility that vacuum pumps in various General Motors vehicles may vary in performance has caused the company to conduct a recall of General Motors vehicles due to vacuum pump issues.

According to the “Frequently Asked Questions” document provided by the manufacturer, General Motors has decided that a defect, which relates to motor vehicle safety exists in the following vehicles:

2014 – 2018 Cadillac Escalade
2014 – 2018 Chevrolet Silverado
2014 – 2018 Chevrolet Suburban
2014 – 2018 Chevrolet Tahoe
2014 – 2018 GMC Sierra
2014 – 2018 GMC Yukon

The defect

Within the GM vehicles that contain the mechanical vacuum pump defect, the engine-mounted output may decrease over time, diminishing the power brake assist and therefore increasing the distance required to stop the vehicle.

Ultimately, this leads to a greater chance of an accident and adds to other risks that Chevrolet vehicles have presented during collision events.

According to documents filed with the National Highway Traffic Safety Administration, the number of vehicles that potentially contain the defect is greater than 3,450,000, with GM estimating that 2 percent of the autos in that total are almost certainly affected by this issue.

The following vehicles make up the group possibly saddled with the vacuum pump problem:

Cadillac Escalade 2015 – 2017
Chevrolet Silverado 1500 2014 – 2018
Chevrolet Suburban 2015 – 2018
Chevrolet Tahoe 2015 – 2018
GMC Sierra 1500 2014 – 2018
GMC Yukon 2015 – 2018

There are certain symptoms that drivers may experience if their car is among those affected by the vacuum pump defect. For instance, they may feel a vibration in the brake pedal or experience a change in the amount of pressure required to depress the brake.

Other possible signs of the problem include a ticking noise coming from within the engine compartment and unintentional activation of the secondary hydraulic brake assist system, according to GM.

Finally, the manufacturer noted that if the vacuum level drops to a level below 10 kPA, a “Service Brake Assist” message will appear in the Driver Information Center within five minutes.

GM has determined that while the defect may potentially increase the possibility of collision, all of these vehicles are otherwise safe to drive before undergoing repair of the vacuum pump.

Timeline of events

According to a chronology provided by GM, the NHTSA opened a preliminary investigation into the subject in November 2018, at which point the manufacturer also began an internal investigation of the same issue.

In December, after reviewing the results of both investigations, GM’s Safety & Field Action Decision Authority decided to extend the warranty on vacuum pumps for all the vehicles listed above.

Then, in July 2019, GM received results of the additional investigation into the subject by the NHTSA, which prompted yet another internal inquiry on the part of the manufacturer.

This final study concluded on August 29, 2019, when GM decided to conduct an official recall on the automobiles to provide them with new software calibration.

Dealers were notified of the recall in early September 2019, with GM planning to send direct notifications to affected drivers in the near future.

The solution

Vehicles that contain the defect can be brought to a local dealership, where the dealer will reprogram the electronic brake control module with a new calibration that corrects the problem, should the vacuum assist become depleted.

As with the potentially dangerous Takata airbag issue reported in early 2021, drivers with a vehicle involved in the recall will be notified by mail. There will be no cost to vehicle owners for repair or repair. Check your car’s recall status using MotorSafety’s free vehicle recall lookup tool.

Spat of Hand Injuries Sparks Massive Ford Explorer Recall

September 16, 2019 Sean Reyes Ford Recalls

Laguna Hills, CA – Sept. 16, 2019 – Ford Motor Company is pulling hundreds of thousands of 2017 Explorer sport utility vehicles from the marketplace due to a seating flaw that likely occurred during manufacturing. When passengers reach for the power front seat lever, sharp edges along the seat frame may cause injury. Dozens of people have claimed as much to authorities.

The 2017 Ford Explorer seat recall will officially begin Oct. 14. Owners who receive a notification are urged to take their vehicle to an area dealership. The SUV will be inspected and a replacement seat will be installed free of charge if it’s necessary.

The Defect

According to filings with the National Highway Traffic Safety Administration, Ford is recalling 311,228 2017 Ford Explorer SUVs from the supply chain over concerns that some of the passengers seats may have sharp components jutting out of the framing. If someone were to brush the problematic portions of the seat, or reach for something in proximity to what’s protruding, they may be hurt. Thus far, there have been 31 reports of individuals whose hands were scratched or scarred as a result of this flaw.

Timeline of Events

This 2017 Ford Explorer seat recall was precipitated by three reports submitted to Ford’s Critical Concern Review Group. The automaker learned at least 30 people had been injured when reaching between the console and power seat. A month later, Ford determined that these injuries were likely due to the sharp edge of the metal seat frame, which apparently escaped the attention of quality control. The automaker determined a recall was the best path forward and contacted NHTSA this summer to make the action official.

The Solution

Ford intends to begin notifying owners in mid-October. Those that receive a mailer should take their vehicle to a dealership. A new seat will replace the problematic at no cost.

For more information on the 2017 Ford Explorer seat recall or other recent Ford recall actions, visit MotorSafety.org.

Potential Air Bag Tear Raises Red Flag For Mercedes-Benz

August 30, 2019 Sean Reyes Mercedes-Benz Recalls

Laguna Hills, CA – Aug. 29, 2019 – Mercedes-Benz is recalling hundreds of its sports cars due to the potential of the front passenger side air bag tearing upon deployment. Such a scenario could increase the risk of serious injury in the event of a crash. This 2018-2019 Mercedes-Benz air bag recall action is slated to begin in early fall, when the luxury automaker will officially alert owners of this safety issue. Motorists can take their vehicles to an area dealership so the problem can be addressed at no cost to them.

The Defect

According to official paperwork filed through the National Highway Traffic Safety Administration, Mercedes Benz is pulling approximately 457 of its sports cars from circulation over the possibility that some of the installed air bags are flawed. At some point during the manufacturing or installation process, the problematic air bags may have been improperly sewn along the seams, which increases the risk that they may be unable to inflate once triggered in a collision. Here are the vehicles involved, each of which have model years between 2018 and 2019:

Mercedes-Benz AMG SL63
Mercedes-Benz AMG SL65
Mercedes-Benz SL450
Mercedes-Benz SL550

Of the 457 vehicles whose passenger-side air bags may be defective, the lion’s share – 232 – are SL450s. However, all the automobiles were built within the same time frame, stretching between March 20 and Nov. 22 of 2018.

Timeline of Events

The luxury automaker’s air bag supplier reached out to Mercedes-Benz in Sept. 2018 to alert the company that during testing of passenger side air bags, one broke apart. This led to a follow-up investigation a couple of months later to determine if this development was isolated or systemic. The inquiry ultimately concluded that “the potential for impaired air bag function could not be ruled out,” even though testing proved that the restraint function would not be fundamentally altered if a tear did occur.

The Solution

Mercedes-Benz plans on informing owners of this problem by first-class mail starting Oct. 1. Recipients of the notifications are asked to take their motor vehicle to an area dealership so a replacement bag can be installed as a precaution.

For more information on this recall or others involving Mercedes-Benz, visit MotorSafety.org.

The defect

Timeline of events

The solution

The Defect

Timeline of Events

The Solution

The Defect

Timeline of Events

The Solution

The Defect

Timeline of Events

Solution

The defect

Timeline of events

The solution

The Defect

Timeline of Events

The Solution

The defect

Timeline of events

The solution

The defect

Timeline of events

The solution

The Defect

Timeline of Events

The Solution

The Defect

Timeline of Events

The Solution

Recent Posts

Archives

Categories